OFFROADSUBARUS.COM

Go Back   OFFROADSUBARUS.COM > Technical Forums > Bolt-On Bits, Accessories and Protection

Notices

Reply
Thread Tools Display Modes
  #41  
Unread 22nd May 2016, 05:22 PM
gregjet's Avatar
gregjet gregjet is offline
Forum Member
 
Join Date: Aug 2015
Location: Bundaberg, Qld. Australia
Year: 2014
Model: xv
Transmission: manual
Posts: 171
gregjet is on a distinguished road
Default

You belted it and it didn't shatter? That is interesting. As far as I know the trick with Al casting it to slow cool them. If they form bigger crystals and/or if they have a higher copper content, they tend to bend rather than break immediately. Adding scandium also works brilliantly, but getting a copper/scandium doped cast aluminium might be a little hopeful I fear.
I have just discovered a fibre that has been around for a while called innegra that I didn't know about. Very light and VERY tough in composites. I was looking for a kevlar supplier to make skid plated for the transmission and diffs when I found it. If I can find a supplier for both I think I will have a go at using them to make the aforementioned. If that works I will try a engine bash plate. Innegra is way cheaper than kevlar and carbon.
Reply With Quote
  #42  
Unread 29th May 2016, 01:04 AM
Vert Vert is offline
Forum Member
 
Join Date: Apr 2016
Location: NSW AUSTRALIA
Year: 2007
Model: Forester x
Transmission: Auto
Posts: 95
Vert is on a distinguished road
Default

Quote:
Originally Posted by Taroona View Post
Who has one of these fitted to their Forester? and how much ground clearance did you loose?
Mate fitted my xtreme one up on a 07 for forester. At front flat bolt up part was about 330mm to ground at lowest base of it was about 230mm .

Also note doing this on a non level driveway so results could vary.

Hope that helps.
Reply With Quote
  #43  
Unread 25th October 2017, 08:34 AM
Ben Up North's Avatar
Ben Up North Ben Up North is offline
can only hope to improve
 
Join Date: Sep 2017
Location: FNQ
Year: 2004 | 1992
Model: SG Forester X MY05 | 92 SVX
Transmission: 5MT D/R | 4EAT
Posts: 846
Ben Up North is on a distinguished road
Default

Quote:
Originally Posted by gregjet View Post
I have just discovered a fibre that has been around for a while called innegra that I didn't know about. Very light and VERY tough in composites. I was looking for a kevlar supplier to make skid plated for the transmission and diffs when I found it. If I can find a supplier for both I think I will have a go at using them to make the aforementioned. If that works I will try a engine bash plate. Innegra is way cheaper than kevlar and carbon.
Hi gregjet, did you have any joy with the Innegra?
Cheers,
Ben
Reply With Quote
  #44  
Unread 25th October 2017, 09:17 AM
duncanm's Avatar
duncanm duncanm is offline
Forum Member
 
Join Date: Sep 2014
Location: Sydney
Year: 1998
Model: Outback. JDM TT conversion
Transmission: 5MT DR
Posts: 533
duncanm is on a distinguished road
Default

http://www.shapers.com.au/2oz-innegr...oard-cloth-30/
__________________
TT Outback
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -3. The time now is 11:21 PM.


Powered by vBulletin®
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.