OFFROADSUBARUS.com

Go Back   OFFROADSUBARUS.com > Technical Forums > Transmission and Driveline

Notices

User Tag List

Reply
 
Thread Tools
  #21  
Old 19th November 2013, 08:43 PM
idw's Avatar
idw idw is offline
Senior Member
 
Join Date: Jun 2012
Location: out bush
Posts: 1,049
idw is on a distinguished road
Default

Are you using subaru cv's and hilux boots taza or aftermarket cv's? I've managed to flog out the aftermarket ones i bought in 60,000k's thinking of going oem
Reply With Quote
  #22  
Old 8th February 2014, 08:41 PM
NachaLuva's Avatar
NachaLuva NachaLuva is offline
Senior Member / Product Developer
Contributing Member
 
Join Date: Oct 2011
Location: SE Melbourne
Posts: 5,275
NachaLuva is on a distinguished road
Default

I didnt take off the brakes when I did mine, just used a punch to knock out the axle from the hub. Pretty much did it this way:

__________________
SUBIELIFTOZ, QUALITY LIFT KITS FOR SUBARUS
1" & 2" lift kits; custom lift kits; all models
Reply With Quote
  #23  
Old 9th February 2014, 09:04 AM
jf1sf5's Avatar
jf1sf5 jf1sf5 is offline
Senior Member
 
Join Date: Aug 2012
Location: Geneva, Switzerland
Posts: 1,249
jf1sf5 is on a distinguished road
Default

I don't do it this way...

I take the wheel off, then unbolt the sway bar, the wishbone from the chassis and out it comes, very easy !

Same for the rear, just take the long bolt out (the one that holds the 2 lateral links), and you don't even need to remove the sway bar !
__________________
Quaife f/r, HotBits, DCCD, 1,59:1, EJ22
Reply With Quote
  #24  
Old 8th June 2014, 11:15 AM
Fazed's Avatar
Fazed Fazed is offline
Senior Member
 
Join Date: May 2014
Location: Australia
Posts: 204
Fazed is on a distinguished road
Default

Does the SG Forester have the pin at the gearbox end that you need to knock out to remove the shaft?
Reply With Quote
  #25  
Old 8th June 2014, 09:02 PM
taza's Avatar
taza taza is offline
Senior Member
 
Join Date: Oct 2010
Location: Perth, Western Australia
Posts: 3,837
taza is on a distinguished road
Default

Nope. You use a large pry bar and pop it out. Be aware that when you do this most of your gearbox oil will come out. It might be a better idea to drain iy first.

Then removr the two strut bolts, turn the hub to the side and pull it out of the hub first then out of the gearbox.

I can usually get the job done in around 20mins to grt in or out.
If you get stuck send me a message.
__________________
Current vehicle - 84 MY Wagon EJ22 4 Speed
Reply With Quote
  #26  
Old 8th June 2014, 09:07 PM
MiddleAgeSubie MiddleAgeSubie is offline
Senior Member
Contributing Member
 
Join Date: Dec 2013
Location: AZ
Posts: 611
MiddleAgeSubie is on a distinguished road
Default

Forum member Superu_legacy has had nothing to contribute here?
__________________
2013 H6 5EAT OB with SubieLiftOZ kit, 2008 Tribeca
(2006 B9; 1995 Legacy wagon).
Reply With Quote
  #27  
Old 9th June 2014, 09:30 AM
NachaLuva's Avatar
NachaLuva NachaLuva is offline
Senior Member / Product Developer
Contributing Member
 
Join Date: Oct 2011
Location: SE Melbourne
Posts: 5,275
NachaLuva is on a distinguished road
Default

Taza, dont remove the strut bolts as that removes your camber setting, requiring a wheel alignment. Just pop out the ball joint from the hub (remove the bolt then open the housing with a screwdriver) then swing the whole strut out & the shaft comes out of the gearbox. First loosen the axle in the hub end by tapping with a hammer.
__________________
SUBIELIFTOZ, QUALITY LIFT KITS FOR SUBARUS
1" & 2" lift kits; custom lift kits; all models
Reply With Quote
  #28  
Old 9th June 2014, 09:36 AM
Fazed's Avatar
Fazed Fazed is offline
Senior Member
 
Join Date: May 2014
Location: Australia
Posts: 204
Fazed is on a distinguished road
Default

Just mark the bolts before you remove. Put back in same location. I prefer to take out strut bolts than bash out ball joints.
Reply With Quote
  #29  
Old 9th June 2014, 03:33 PM
jf1sf5's Avatar
jf1sf5 jf1sf5 is offline
Senior Member
 
Join Date: Aug 2012
Location: Geneva, Switzerland
Posts: 1,249
jf1sf5 is on a distinguished road
Default

No one else doing it my way ?
__________________
Quaife f/r, HotBits, DCCD, 1,59:1, EJ22
Reply With Quote
  #30  
Old 10th June 2014, 07:23 AM
idw's Avatar
idw idw is offline
Senior Member
 
Join Date: Jun 2012
Location: out bush
Posts: 1,049
idw is on a distinguished road
Default

It's easier to remove the 14mm grub screw that holds the ball joint into the hub than remove the strut bolts i find.
Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -3. The time now is 04:36 PM.


Powered by vBulletin®
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.